To Order Call: 800-817-3486 or Email: sales@mpimorheat.com or Fill a Contact Form

Shipped from Stock

Information

The limit control L91 is an over temperature or a high limit safety device with a latching output that could remove the power while the process is in abnormal condition, for example the process higher than high limit set point or lower than the low limit set point.

SPECIFICATIONS
Power 
90 – 250 VAC, 47 – 63 Hz, 10VA, 5W maximum
11 – 26 VAC / VDC, SELV, Limited Energy, 10VA, 5W maximum
Signal InputCharacteristics 
Resolution18 bits
Sampling Rate5 times / second
Maximum Rating-2 VDC minimum, 12 VDC maximum( 1 minute for mA input )
Temperature Effect±1.5 uV/ °C 
Sensor Lead Resistance EffectT/C: 0.2uV/ohm
3-wire RTD: 2.6 °C/ohm of resistance difference of two leads
2-wire RTD: 2.6 °C/ohm of resistance sum of two leads
Burn-out Current200nA
Common Mode Rejection Ratio ( CMRR ) 120dB
Sensor Break DetectionSensor open for TC, RTD and mV inputs,
below 1 mA for 4-20 mA input,
below 0.25V for 1 – 5 V input, unavailable for other inputs.
Sensor Break Responding TimeWithin 4 seconds for TC, RTD and mV inputs,
0.1 second for 4-20 mA and 1 – 5 V inputs.
Characteristics
TypeRange Accuracy@ 25 °CInput Impedance
J-120 ~ 1000 °C (-184 ~ 1832 °F)±2 °C2.2MΩ
K-200 ~ 1370 °C (-328 ~ 2498°F)±2 °C2.2MΩ
T-250 ~ 400°C (-418 ~ 752°F)±2 °C2.2MΩ
E-100 ~ 900 °C (-148 ~ 1652 °F)±2 °C2.2MΩ
B0 ~ 1820 °C (32 ~ 3272 °F)±2 °C (200°C – 1820°C)2.2MΩ
R0 ~ 1767.8 °C (32 ~ 3214 °F)±2 °C2.2MΩ
S0 ~ 1767.8 °C (32 ~ 3214 °F)±2 °C2.2MΩ
N-250 ~ 1300 °C (-418 ~ 2372 °F)±2 °C2.2MΩ
L-200 ~ 900 °C (-328 ~ 1652 °F)±2 °C2.2MΩ
PT100 (DIN)-210 ~ 700 °C (-346 ~ 1292 °F)±0.4°C1.3KΩ
PT100 (JIS)-200 ~ 600 °C (-328 ~ 1112 °F)±0.4°C1.3KΩ
mV-8 ~ 70mV±0.05%2.2MΩ
mA-3 ~ 27mA±0.05%70.5Ω
V-1.3 ~ 11.5V±0.05%510KΩ
Event Input
Logic LowLogic -10V minimum, 0.8V maximum.
Logic High2V minimum, 10V maximum.
FunctionsRemote reset, remote lockout.
Output 1 / Output 2 
Relay Rating2A/240 VAC, life cycles 200,000 for resistive load
Pulsed VoltageSource Voltage 5V, current limiting resistance 66Ω
Triac ( SSR ) Output 
Rating1A / 240 VAC
Inrush Current20A for 1 cycle
Min. Load Current50 mA rms
Max. Off-state Leakage3 mA rms
Max. On-state Voltage1.5V rms
Insulation Resistance1000 Mohms min. at 500 VDC
Dielectric Strength2500 VAC for 1 minute
DC Voltage Supply Characteristics ( Installed at Output 2 )
TypeToleranceMax. Output Current Ripple VoltageIsolation Barrier
20V±1 V25 mA0.2 Vp-p500 VAC
12V±0.6 V40 mA0.1 Vp-p500 VAC
5V±0.25 V80 mA0.05 Vp-p500 VAC
Data Communication 
InterfaceRS-232 ( 1 unit ), RS-485 ( up to 247 units )
Protocol Modbus Protocol RTU mode
Address1 – 247
Baud Rate0.3 ~ 38.4 Kbits/sec
Data Bits8 bits
Parity BitNone, Even or Odd
Stop Bit1 or 2 bits
Communication Buffer50 bytes
User Interface
4-digit LED Displays0.4″ (10mm),
Keypad4 keys
Programming Port For automatic setup, calibration and testing
Communication PortConnection to PC for supervisory control
Limit Control
High Limit, Low Limit and High/Low Limit programmable

 

Digital Filter 
FunctionFirst order
Time Constant 0, 0.2, 0.5, 1, 2, 5, 10, 20, 30, 60 seconds programmable
Environmental & Physical 
Operating Temperature-10°C ~ 50°C
Storage Temperature-40°C ~ 60°C
Humidity0 to 90 % RH ( non-condensing )
Insulation Resistance20 Mohms min. ( at 500 VDC )
Dielectric Strength2000 VAC, 50/60 Hz for 1 minute
Vibration Resistance10 – 55 Hz, 10 m/s² for 2 hours
Shock Resistance200 m/s2( 20 g )
MoldingsFlame retardant polycarbonate
Dimensions48mm(W) X 48mm(H) X 94mm(D), 86 mm depth behind panel
Weight 150 grams
Approval Standards
SafetyFM Class 3545 (Oct. 1998), UL873 ( 11’th edition, 1994 ) , CSA C22.2 No. 24-93 , EN61010-1 (IEC1010-1)
Protective ClassIP30 front panel, indoor use,
IP20 housing and terminals ( with protective cover)
EMCEN61326